Your Complete Tutorial for Installing a Bathtub
Call TodayThis great article down below pertaining to How to Install a Bathtub is absolutely attention-grabbing. Have a go and make your own final thoughts.
Mounting a bath tub isn't specifically brain surgery, but it does call for solid plumbing, carpentry, and also sometimes, tiling skills. Changing an old bathtub with a new one is also a reasonably challenging project. If the old bathtub is readily easily accessible, the task can relocate quickly; if you have to open a wall surface to get rid of the old bathtub and place the brand-new tub, the task is much harder. In either situation, the task is within a residence handyman's skills, although you will certainly require a helper to move out the old tub and set in the brand-new one. Make certain you have actually qualified yourself for the task and also are comfortable attempting it. As opposed to hiring a professional to take control of a halfway-completed task, it is better to think about using one prior to you start. Opportunities are you may need a specialist plumber to make tube connections.
This short article will assist you mount a brand-new bathtub in your restroom if you have actually already purchased a new bathtub and also don't need to alter the arrangement of your previous water supply pipes.
Your devices and material list need to make up the following:
Getting ready for the Installation
Firstly, the supporting structure provided with the bathroom should be fitted (if required) according to the producer's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is necessary to see to it that if the tap comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets unit to stop strain on the tub.
Fit the flexible tap adapters to the bottom of the two taps making use of 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you utilize all of the supplied washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath must now be ready to be suited its final position.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your setup, after that the first thing you should do is detach the water system. After doing so, turn on the faucets to drain pipes any kind of water staying in the system. The procedure of eliminating the existing taps can be fairly bothersome as a result of the restricted access that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the staying water that will certainly originate from the pipes. As soon as the supply pipes have actually been removed, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from turning during this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing substance.
Before moving on to fit the new taps, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Setting up the Bathtub
Using the two wooden boards under its feet, position the bathtub in the called for setting. The wood boards are handy in evenly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four tiny factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be attained by checking the spirit level and also changing the feet on the tub up until the spirit level reviews level.
To set up taps, fit the bottom of the outermost adaptable tap adapter to the appropriate supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Turn on the water supply and also check all joints and also brand-new pipework for leaks and also tighten them if necessary. Fill the bathtub and also inspect the overflow outlet and also the typical outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the manufacturer's user's manual. Tiling and sealing around the bath tub ought to wait until the bathtub has been utilized at the very least when as this will settle it into its last setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic port to prevent damage to the thread. One end of the port fits on the plastic tail of the tap and also the various other end provides a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the mounting hole in the bath/basin making certain that the washing machines remain in place in between the tap and also the sink. Secure the faucet in position with the maker provided backnut. When the faucet is safely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The former kind ought to be linked to the tap finishes initially, tightening up just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to fracture a stiff seal, causing the water to permeate the wall surface in between the bathroom and the tiling, resulting in complications with dampness as well as possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your fixtures as well as fittings. They are marketed in tubes as well as cartridges, as well as are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched paper or soft rope. Bear in mind to constantly fill the bathtub with water before securing, to enable the activity experienced when the bathtub remains in use. The sealant can break relatively early if you do not consider this activity prior to securing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally conveniently available on the marketplace. It is recommended to fit the tiles making use of water-resistant or waterproof glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like reading about How to Install a Bathtub Yourself? Leave a remark further down. We would be delighted to know your opinion about this write up. We hope to see you back again in the near future. Sharing is caring. Who knows, you will be helping someone out. We treasure reading our article about How to Install a Bathtub Yourself.
Set An Appointment